18 90 60 30 0 90 60 30 0 50 100% 50 100% 90 60 30 0 90 60 30 0 50 100% 50 100% 90 60 30 0 90 60 30 0 50 100% 50 100% 90 60 30 0 90 60 30 0 50 100% 50 100% absolute maximum ratings (ta=25 c) symbol unit ratings i f ma 30 i fp ma 100 v r v3 top c C30 to +85 tstg c C30 to +100 outline drawing a n sel6014 series (wide viewing angle) outline drawing c outline drawing b n sel6015 series (narrow viewing angle) l sel6000 series leds pack- aged on tapes can withstand shocks caused by insertion ma- chines; thus, they can be con- tact-mounted automatically on circuit boards. recommended dimensions of insertion holes on printed cir- cuit boards viewing angle sel6010 series sel6014 series sel6015 series n sel6010 series (standard type) viewing angle of a diffused lens n external dimensions: unit: mm tolerance: 0.3 round-type contact mount leds (for automatic insertion) 0.9 ~ 1.0 2.54mm viewing angle of a non-diffused lens viewing angle of a non-diffused lens viewing angle of a non-diffused lens sel6210r sel6414e sel6915a 3.5 0.8 ?.2 4.0 ?.2 0.4 ?.1 23.0min 1.0min 4.5 ?.5 (1.6) 2.5 ?.1 (p.2.54) 3.5 4.4 0.45 ?.1 0.65max resin heap 0.8max cathode 3.5 0.8 ?.2 4.0 ?.2 0.4 ?.1 23.0min 1.0min (1.7) 3.5 ?.1 (p.2.54) 3.1 ?.1 4.4 0.45 ?.1 0.65max resin heap 0.8max resin burr 0.3max cathode mark cathode 3.5 0.8 ?.2 4.0 ?.2 0.4 ?.1 23.0min 1.0min 5.5 ?.5 (1.7) 3.5 ?.1 (p.2.54) 3.1 ?.1 4.4 0.45 ?.1 0.65max resin heap 0.8max cathode
19 i v (mcd) i r ( m a) dl l p max v f (v) sel6210r sel6210s sel6410g sel6410e sel6510g sel6510c sel6710y SEL6710K sel6810d sel6810a sel6910d sel6910a sel6214s sel6414e sel6514c sel6814a sel6914a sel6215s sel6415e sel6515c sel6815a sel6915a outline drawing condition i f (ma) condition v r (v) condition i f (ma) (nm) typ emitting color max typ green pure green yellow amber orange high intensity red green pure green amber orange high intensity red green pure green amber orange 50 3 2.5 10 50 3 2.5 10 50 3 2.5 10 12 25 15 45 5 16 5 15 4 10 6.5 14 10 12 6 5 5 30 50 18 30 40 630 560 555 570 610 587 630 560 555 610 587 630 560 555 610 587 35 20 40 35 33 35 20 35 33 35 20 35 33 a c b 20 10 20 10 20 n using contact mount leds packaged on tapes 1. printed circuit board l one-side printed circuit board is recommended. l if there are several smd parts on the same printed circuit board, insert the leds after the adhesive for other smd parts hardened. 2. insertion conditions l use low insertion pusher pressure, as much as possible. l cut and clinch: panasert t pattern is recommended. for n pattern, make the clinching angle of the leds anode as small as possible. 3. soldering conditions l preheating must be less than 90 c (temperature on printed circuit boards bottom surface) for no more than two minutes l solder dipping must be made at a temperature of 250 c for no more than 3 seconds. type no. display form ( ? : mm) type of lens l 3.1 l 3.1 l 3.1 l 3.1 l 3.1 l 3.1 l 3.1 l 3.1 l 3.1 l 3.1 l 3.1 l 3.1 l 3.5 l 3.5 l 3.5 l 3.5 l 3.5 l 3.1 l 3.1 l 3.1 l 3.1 l 3.1 electro-optical characteristics (ta=25 c) red tinted, diffused red tinted, non-diffused green tinted, diffused green tinted, non-diffused green tinted, diffused un-tinted, non-diffused yellow tinted, diffused yellow tinted, non-diffused orange tinted, diffused orange tinted, non-diffused orange tinted, diffused orange tinted, non-diffused red tinted, non-diffused green tinted, non-diffused un-tinted, non-diffused orange tinted, non-diffused orange tinted, non-diffused red tinted, non-diffused green tinted, non-diffused un-tinted, non-diffused orange tinted, non-diffused orange tinted, non-diffused high intensity red typ 1.9 2.0 1.9 1.9 2.0 1.9 1.9 2.0 1.9
|
